Difference between x86, x32, and x64 architectures?_问答_开发者

Please explain the differe开发者_运维问答nce between x86, x32 and x64? Its a bit confusing when it comes to x86 and x32 because most of the time 32-bit programs run on x86...

Hans and DarkDust answer covered i386/i686 and amd64/x86_64, so there's no sense in revisiting them. This answer will focus on X32, and provide some info learned after a X32 port.

x32 is an ABI for amd64/x86_64 CPUs using 32-bit integers, longs and pointers. The idea is to combine the smaller memory and cache footprint from 32-bit data types with the larger register set of x86_64. (Reference: Debian X32 Port page).

x32 can provide up to about 30% reduction in memory usage and up to about 40% increase in speed. The use cases for the architecture are:

vserver hosting (memory bound)
netbooks/tablets (low memory, performance)
scientific tasks (performance)

x32 is a somewhat recent addition. It requires kernel support (3.4 and above), distro support (see below), libc support (2.11 or above), and GCC 4.8 and above (improved address size prefix support).

For distros, it was made available in Ubuntu 13.04 or Fedora 17. Kernel support only required pointer to be in the range from 0x00000000 to 0xffffffff. From the System V Application Binary Interface, AMD64 (With LP64 and ILP32 Programming Models), Section 10.4, p. 132 (its the only sentence):

10.4 Kernel Support
Kernel should limit stack and addresses returned from system calls between 0x00000000 to 0xffffffff.

When booting a kernel with the support, you must use syscall.x32=y option. When building a kernel, you must include the CONFIG_X86_X32=y option. (Reference: Debian X32 Port page and X32 System V Application Binary Interface).

Here is some of what I have learned through a recent port after the Debian folks reported a few bugs on us after testing:

the system is a lot like X86
the preprocessor defines __x86_64__ (and friends) and __ILP32__, but not __i386__/__i686__ (and friends)
you cannot use __ILP32__ alone because it shows up unexpectedly under Clang and Sun Studio
when interacting with the stack, you must use the 64-bit instructions pushq and popq
once a register is populated/configured from 32-bit data types, you can perform the 64-bit operations on them, like adcq
be careful of the 0-extension that occurs on the upper 32-bits.

If you are looking for a test platform, then you can use Debian 8 or above. Their wiki page at Debian X32 Port has all the information. The 3-second tour: (1) enable X32 in the kernel at boot; (2) use debootstrap to install the X32 chroot environment, and (3) chroot debian-x32 to enter into the environment and test your software.

x86 refers to the Intel processor architecture that was used in PCs. Model numbers were 8088 (8 bit bus version of 8086 and used in the first IBM PC), 8086, 286, 386, 486. After which they switched to names instead of numbers to stop AMD from copying the processor names. Pentium etc, never a Hexium :).

x64 is the architecture name for the extensions to the x86 instruction set that enable 64-bit code. Invented by AMD and later copied by Intel when they couldn't get their own 64-bit arch to be competitive, Itanium didn't fare well. Other names for it are x86_64, AMD's original name and commonly used in open source tools. And amd64, AMD's next name and commonly used in Microsoft tools. Intel's own names for it (EM64T and "Intel 64") never caught on.

x32 is a fuzzy term that's not associated with hardware. It tends to be used to mean "32-bit" or "32-bit pointer architecture", Linux has an ABI by that name.

x86 means Intel 80x86 compatible. This used to include the 8086, a 16-bit only processor. Nowadays it roughly means any CPU with a 32-bit Intel compatible instruction set (usually anything from Pentium onwards). Never read x32 being used.

x64 means a CPU that is x86 compatible but has a 64-bit mode as well (most often the 64-bit instruction set as introduced by AMD is meant; Intel's idea of a 64-bit mode was totally stupid and luckily Intel admitted that and is now using AMDs variant).

So most of the time you can simplify it this way: x86 is Intel compatible in 32-bit mode, x64 is Intel compatible in 64-bit mode.

As the 64bit version is an x86 architecture and was accordingly first called x86-64, that would be the most appropriate name, IMO. Also, x32 is a thing (as mentioned before)—‘x64’, however, is not a continuation of that, so is (theoretically) missleading (even though many people will know what you are talking about) and should thus only be recognised as a marketing thing, not an ‘official’ architecture (again, IMO–obviously, others disagree).